ARCHIVES

Lepar Hilir Biogas Power Plant Exporting 1.5MW to the National Grid

PROJECT BY CONCORD GROUP

Background of the project

Lepar Hilir Biogas Power Plant located at FGV’s Lepar Hilir Palm Oil Mill in Pahang, is a Waste-to-Wealth project, conceptualized by Concord under the Build-Own-Operate (BOO) model.  This plant treats palm oil mill effluent (POME), captures its biogas for power generation and sells 1.5MW electricity to Tenaga Nasional Berhad (TNB), which is governed by the Renewable Energy Power Purchase Agreement (RePPA) under the Feed-in-Tariff (FiT) Scheme, quota issued by Sustainable Energy Development authority (SEDA) Malaysia (SEDA).

Palm oil mills produce effluent which is considered as waste and pollutes the environment. It also releases biogas which contains methane, a greenhouse gas 21 times more potent than carbon dioxide.  The captured methane is used as fuel to generate electricity that is then sold to TNB under the FiT mechanism at a fixed rate.

Concord Group sees the potential of transforming and valorizing the POME into wealth by constructing the FGV Lepar Hilir Biogas plant in Pahang, Malaysia.

This plant is financed, owned, constructed and operated by Concord under the BOO business model and was commissioned in December 2018.   This project addresses greenhouse gas emission issues in the palm oil industry and valorizes it into a form of renewable energy.  The development of the biogas power plant initiated a value chain of activity within the local communities which has a direct impact on three Ps (People, Planet and Profits).  It promotes sustainable practices by performing a truly circular economy business model.

Project execution of this project has also set a new benchmark for this industry.  It was successfully commissioned within 14 months followed by another 3 similar plants within a period of 6 months.  It meets the expectations of all related project stakeholders i.e. shareholders, mill owners, financial institutions, authorities, vendors, state and federal governments.

Contribution of this project to the Industry, Country (Malaysia), ASEAN, World

Concord Group also gives back to the industry and community through Corporate Social Responsibility (CSR) initiatives such as experience-sharing programs on safety and health in biogas plants and providing internship placement opportunities for students.

A higher awareness of the benefits to use biogas as renewable energy has been embedded among the palm oil mill owners, which will bring us to achieve the collective aspiration target of 23% primary energy mix by 2035 within the ASEAN countries, being a region of palm oil producing countries.

This plant will also help Malaysia to achieve its RE target of energy generation mix to 20% by 2025.

In long run, the world will change their perception towards palm oil industry with these sustainable practices.

We capture biogas to reduce the climate change effect of the palm oil industry and simultaneously generate green energy to reduce the dependency on fossil fuel as the world moves towards renewable energy and diversification of energy sources. 

Overall, the success of this initiative has proven that renewable energy can provide a great business model, while contributing to sustainability in this industry.

Showing Archived File

PROJECT BY CONCORD GROUP

Background of the project

Lepar Hilir Biogas Power Plant located at FGV’s Lepar Hilir Palm Oil Mill in Pahang, is a Waste-to-Wealth project, conceptualized by Concord under the Build-Own-Operate (BOO) model.  This plant treats palm oil mill effluent (POME), captures its biogas for power generation and sells 1.5MW electricity to Tenaga Nasional Berhad (TNB), which is governed by the Renewable Energy Power Purchase Agreement (RePPA) under the Feed-in-Tariff (FiT) Scheme, quota issued by Sustainable Energy Development authority (SEDA) Malaysia (SEDA).

Palm oil mills produce effluent which is considered as waste and pollutes the environment. It also releases biogas which contains methane, a greenhouse gas 21 times more potent than carbon dioxide.  The captured methane is used as fuel to generate electricity that is then sold to TNB under the FiT mechanism at a fixed rate.

Concord Group sees the potential of transforming and valorizing the POME into wealth by constructing the FGV Lepar Hilir Biogas plant in Pahang, Malaysia.

This plant is financed, owned, constructed and operated by Concord under the BOO business model and was commissioned in December 2018.   This project addresses greenhouse gas emission issues in the palm oil industry and valorizes it into a form of renewable energy.  The development of the biogas power plant initiated a value chain of activity within the local communities which has a direct impact on three Ps (People, Planet and Profits).  It promotes sustainable practices by performing a truly circular economy business model.

Project execution of this project has also set a new benchmark for this industry.  It was successfully commissioned within 14 months followed by another 3 similar plants within a period of 6 months.  It meets the expectations of all related project stakeholders i.e. shareholders, mill owners, financial institutions, authorities, vendors, state and federal governments.

Contribution of this project to the Industry, Country (Malaysia), ASEAN, World

Concord Group also gives back to the industry and community through Corporate Social Responsibility (CSR) initiatives such as experience-sharing programs on safety and health in biogas plants and providing internship placement opportunities for students.

A higher awareness of the benefits to use biogas as renewable energy has been embedded among the palm oil mill owners, which will bring us to achieve the collective aspiration target of 23% primary energy mix by 2035 within the ASEAN countries, being a region of palm oil producing countries.

This plant will also help Malaysia to achieve its RE target of energy generation mix to 20% by 2025.

In long run, the world will change their perception towards palm oil industry with these sustainable practices.

We capture biogas to reduce the climate change effect of the palm oil industry and simultaneously generate green energy to reduce the dependency on fossil fuel as the world moves towards renewable energy and diversification of energy sources. 

Overall, the success of this initiative has proven that renewable energy can provide a great business model, while contributing to sustainability in this industry.

MIE Industrial Sdn. Bhd.

About MIE Industrial Sdn. Bhd.

MIE Industrial Sdn Bhd, with its headquarter in Puchong, is a full-fledged local EPCC solution provider in Malaysia. Established in 1997, MIE industrial started off as an Electrical and Instrumentation contractor from a humble two-story shop lot office.

In 2015, MIE Industrial marks a major milestone by having CTCI on board as their strategic partner. CTCI is a Taiwan-based EPC company with offices worldwide and known over for their engineering and construction expertise. With CTCI expansive engineering and working experience, MIE Industrial grew its engineering force to now 90-plus engineers from various discipline and backgrounds, all stationed  in-house in its Headquarter. From process, mechanical, piping and solar, MIE Industrial full range of engineering discipline are ready to tackle any engineering request no matter the complexity.

In 2019, MIE Industrial hit another milestone by acquiring Seremban Engineering Berhad, making Seremban Engineering as one of MIE Industrial’s subsidiary. With Seremban Engineering expertise, MIE Industrial has now access to fabrication business, particularly in pressure vessels and storage tanks.

MIE Industrial is also the first EPCC Company to be appointed as KITZ Valve official distributorship for the oil and gas market in Malaysia.  Known world over for its quality, MIE Industrial is now offering to its clients a full range of valve solution such as ball valve, gate valve, actuated on/off valve and globe valve among others.

MIE Industrial is wholly committed to provide clients with a quality and efficient EPCC solution. Always striving for excellence, MIE Industrial is committed to deliver above and beyond clients’ expectation.

Showing Archived File

About MIE Industrial Sdn. Bhd.

MIE Industrial Sdn Bhd, with its headquarter in Puchong, is a full-fledged local EPCC solution provider in Malaysia. Established in 1997, MIE industrial started off as an Electrical and Instrumentation contractor from a humble two-story shop lot office.

In 2015, MIE Industrial marks a major milestone by having CTCI on board as their strategic partner. CTCI is a Taiwan-based EPC company with offices worldwide and known over for their engineering and construction expertise. With CTCI expansive engineering and working experience, MIE Industrial grew its engineering force to now 90-plus engineers from various discipline and backgrounds, all stationed  in-house in its Headquarter. From process, mechanical, piping and solar, MIE Industrial full range of engineering discipline are ready to tackle any engineering request no matter the complexity.

In 2019, MIE Industrial hit another milestone by acquiring Seremban Engineering Berhad, making Seremban Engineering as one of MIE Industrial’s subsidiary. With Seremban Engineering expertise, MIE Industrial has now access to fabrication business, particularly in pressure vessels and storage tanks.

MIE Industrial is also the first EPCC Company to be appointed as KITZ Valve official distributorship for the oil and gas market in Malaysia.  Known world over for its quality, MIE Industrial is now offering to its clients a full range of valve solution such as ball valve, gate valve, actuated on/off valve and globe valve among others.

MIE Industrial is wholly committed to provide clients with a quality and efficient EPCC solution. Always striving for excellence, MIE Industrial is committed to deliver above and beyond clients’ expectation.

Sustainable Printing, Rooted In German Quality Standards

SUSTAINABLE PRINTING, ROOTED IN GERMAN QUALITY STANDARDS

Over 375 million empty toner and ink cartridges are thrown away as scrap every
year – this equates to roughly 11 cartridges every second!

The plastics used in printer cartridges are made from engineering grade polymer which has a very slow decomposition rate ranging between 450 and 1000 years depending on the cartridge type.

Generally, cheap new build compatible cartridges end up going straight to landfill at their end of life due to poor low grade plastics and components that are not of high enough quality standard to
reuse.

freecolor printer cartridges are remanufactured, meaning they are reused. Reuse is the highest form of environmental responsibility. It is superior to recycling in that it doesn’t use non-renewable resources to break down plastic and metal.

Using freecolor remanufactured cartridges will dramatically reduce your carbon footprint by preventing tonnes of toxic material going into landfill.

SUSTAINABLE QUALITY

For more than 20 years now, the freecolor brand has been one of the most successful and bestselling brands in the DACH region (Germany, Austria, Switzerland) – a market where product quality, reliability and sustainability are paramount. In recent years the brand has expanded successfully to international markets.

The freecolor product range has benefited from years and millions of dollars in the development of the most sophisticated manufacturing environment in the document imaging industry. Our in-house R&D and engineering teams ensure that our products meet or exceed OEM performance for yield and print quality through the design and implementation of propriety product development practices, manufacturing standards, process automation, and performance testing protocols.

In state-of-the-art ISO 9001 and ISO 14001 certified production facilities, empty high-quality OEM cores are given a second life when they go a thorough remanufacturing and testing process to become freecolor toner cartridges. Freecolor offers the broadest and deepest product selection, including cartridges that are compatible with all the leading brands. ISO 19752 (monochrome cartridges) and ISO 19798 (colour cartridges) testing standards for page yield, 100% post-production testing and quality toner powder result in a reliable product, only matched by the OEM.

The entire freecolor range represents a true alternative to the OEM, as it combines OEM performance with environmental sustainability and significant savings over the original cartridge.

CERTIFIED SUSTAINABILITY

Quality and sustainability are amongst the key features of our product.

Over the years, freecolor branded cartridges have acquired a
number of certifications to verify our commitment to both:

SUSTAINABLE LOGISTICS AND PACKAGING

Freecolor packaging uses sustainable materials. Long before the plastic pollution problem made international headlines, the majority of our inserts had been switched from plastic airbags to recyclable cardboard inserts.

Our boxes are also made from recyclable cardboard – and they are tailored to best product fit. This allows for more efficient use of cubic capacity, which results in fewer shipments overall thereby significantly reducing CO2 emissions and fossil fuel consumption – leading to an overall reduction in carbon footprint.

OVERVIEW FREECOLOR ADVANTAGES

 Environmentally Sustainable products: remanufacturing = reuse
 OEM-like performance and quality, but with significant cost savings
o ISO 19752 (mono) and ISO 19798 (colour) testing standards for page yield
o ISO 9001 and ISO 14001 certified production facilities
o 100% post-production testing
 Several environmental certifications and compliances
 Sustainable packaging and supply chain
 Comprehensive 3 year warranty
 100% IP-safe products

SUSTAINABLE PRINTING – WITH FREECOLOR TONER CARTRIDGES

Showing Archived File

SUSTAINABLE PRINTING, ROOTED IN GERMAN QUALITY STANDARDS

Over 375 million empty toner and ink cartridges are thrown away as scrap every
year – this equates to roughly 11 cartridges every second!

The plastics used in printer cartridges are made from engineering grade polymer which has a very slow decomposition rate ranging between 450 and 1000 years depending on the cartridge type.

Generally, cheap new build compatible cartridges end up going straight to landfill at their end of life due to poor low grade plastics and components that are not of high enough quality standard to
reuse.

freecolor printer cartridges are remanufactured, meaning they are reused. Reuse is the highest form of environmental responsibility. It is superior to recycling in that it doesn’t use non-renewable resources to break down plastic and metal.

Using freecolor remanufactured cartridges will dramatically reduce your carbon footprint by preventing tonnes of toxic material going into landfill.

SUSTAINABLE QUALITY

For more than 20 years now, the freecolor brand has been one of the most successful and bestselling brands in the DACH region (Germany, Austria, Switzerland) – a market where product quality, reliability and sustainability are paramount. In recent years the brand has expanded successfully to international markets.

The freecolor product range has benefited from years and millions of dollars in the development of the most sophisticated manufacturing environment in the document imaging industry. Our in-house R&D and engineering teams ensure that our products meet or exceed OEM performance for yield and print quality through the design and implementation of propriety product development practices, manufacturing standards, process automation, and performance testing protocols.

In state-of-the-art ISO 9001 and ISO 14001 certified production facilities, empty high-quality OEM cores are given a second life when they go a thorough remanufacturing and testing process to become freecolor toner cartridges. Freecolor offers the broadest and deepest product selection, including cartridges that are compatible with all the leading brands. ISO 19752 (monochrome cartridges) and ISO 19798 (colour cartridges) testing standards for page yield, 100% post-production testing and quality toner powder result in a reliable product, only matched by the OEM.

The entire freecolor range represents a true alternative to the OEM, as it combines OEM performance with environmental sustainability and significant savings over the original cartridge.

CERTIFIED SUSTAINABILITY

Quality and sustainability are amongst the key features of our product.

Over the years, freecolor branded cartridges have acquired a
number of certifications to verify our commitment to both:

SUSTAINABLE LOGISTICS AND PACKAGING

Freecolor packaging uses sustainable materials. Long before the plastic pollution problem made international headlines, the majority of our inserts had been switched from plastic airbags to recyclable cardboard inserts.

Our boxes are also made from recyclable cardboard – and they are tailored to best product fit. This allows for more efficient use of cubic capacity, which results in fewer shipments overall thereby significantly reducing CO2 emissions and fossil fuel consumption – leading to an overall reduction in carbon footprint.

OVERVIEW FREECOLOR ADVANTAGES

 Environmentally Sustainable products: remanufacturing = reuse
 OEM-like performance and quality, but with significant cost savings
o ISO 19752 (mono) and ISO 19798 (colour) testing standards for page yield
o ISO 9001 and ISO 14001 certified production facilities
o 100% post-production testing
 Several environmental certifications and compliances
 Sustainable packaging and supply chain
 Comprehensive 3 year warranty
 100% IP-safe products

SUSTAINABLE PRINTING – WITH FREECOLOR TONER CARTRIDGES

Innovative Solutions to Air and Gas Compression

Registration #: MyHP00048/20

SCR SCREW AIR COMPRESSOR PERMANENT MAGNETIC SERIES

IP65 MOTOR INVERTER CONTROL

MODEL: SCR50PM-8 (50HP) RANGE: 30 – 150 HP

POWER SAVINGS: 35%-40%                

Services We Offer:

  • JKKP Appointed Contractor for NDT Thickness Test
  • Chemical Cleaning & Maintenance Air Tank
  • Anti-Rust Spray Paint Maintenance
  • JKKP PMT Application & Renewal Service
  • After Sales & Services of Air Compressor/ Air Dryer/ Air Filter

CONTACT US NOW

Website: www.scrcompressor.com.my

Email: simontanscr@gmail.com

Tel: 03-5634 8966

H/P: 019-3348766 (Simon Tan)

Penang H/P: 012-4700995 (Alex Goh)

Showing Archived File

Registration #: MyHP00048/20

SCR SCREW AIR COMPRESSOR PERMANENT MAGNETIC SERIES

IP65 MOTOR INVERTER CONTROL

MODEL: SCR50PM-8 (50HP) RANGE: 30 – 150 HP

POWER SAVINGS: 35%-40%                

Services We Offer:

  • JKKP Appointed Contractor for NDT Thickness Test
  • Chemical Cleaning & Maintenance Air Tank
  • Anti-Rust Spray Paint Maintenance
  • JKKP PMT Application & Renewal Service
  • After Sales & Services of Air Compressor/ Air Dryer/ Air Filter

CONTACT US NOW

Website: www.scrcompressor.com.my

Email: simontanscr@gmail.com

Tel: 03-5634 8966

H/P: 019-3348766 (Simon Tan)

Penang H/P: 012-4700995 (Alex Goh)

Cancellation of MyHIJAU Mark Business Clinic Year 2020 Session #3

Greetings from GreenTech Malaysia and MyHIJAU Team!

CANCELLATION OF MyHIJAU MARK BUSINESS CLINIC YEAR 2020 SESSION #3

On Monday 16 March 2020, Prime Minister Tan Sri Muhyiddin Yassin has declared that the entire country will be on a movement control order starting from March 18 to March 31 to deal with the rise in Covid-19 cases.

With that regards we are regret to inform that MyHIJAU MARK BUSINESS CLINIC YEAR 2020 SESSION #3 which scheduled on this coming 25/3/2020 is now being cancelled. We will later notify the new date for session. The cancellation also due to the very less confirmation participation from the companies.

However, we from MyHIJAU Team still can be accessed thru email. If you have any inquiries, we will be glad to help you.

If you have any enquiry, please feel free to contact us:

  1. Mr. Syamiullah email: syamiullah@greentechmalaysia.my        
  2. Pn. Nur Syahira: syahira@greentechmalaysia.my

Once again we would like to apologies and we really appreciate your interest to joint this session and to register under MyHIJAU Mark.

Showing Archived File

Greetings from GreenTech Malaysia and MyHIJAU Team!

CANCELLATION OF MyHIJAU MARK BUSINESS CLINIC YEAR 2020 SESSION #3

On Monday 16 March 2020, Prime Minister Tan Sri Muhyiddin Yassin has declared that the entire country will be on a movement control order starting from March 18 to March 31 to deal with the rise in Covid-19 cases.

With that regards we are regret to inform that MyHIJAU MARK BUSINESS CLINIC YEAR 2020 SESSION #3 which scheduled on this coming 25/3/2020 is now being cancelled. We will later notify the new date for session. The cancellation also due to the very less confirmation participation from the companies.

However, we from MyHIJAU Team still can be accessed thru email. If you have any inquiries, we will be glad to help you.

If you have any enquiry, please feel free to contact us:

  1. Mr. Syamiullah email: syamiullah@greentechmalaysia.my        
  2. Pn. Nur Syahira: syahira@greentechmalaysia.my

Once again we would like to apologies and we really appreciate your interest to joint this session and to register under MyHIJAU Mark.

GreenTech Run 2019 Completed

We are glad to inform that we have successfully conducted GreenTech Run 2019 at our office, Malaysian Green Technology Corporation, Bandar Baru Bangi on 28 December 2019. We would like to thanks all the sponsor and all the participants for the run in order to make this event is a success!

Thank you for the effort!

GreenTech Run 2019 Introduction

Background

GreenTech Run 2019 is the first running event organized by Green Catalyst Division under Malaysian Green Technology Corporation (GreenTech Malaysia) with the intention to promotes healthy lifestyle and eco-friendly life by informing the public on the eco-friendly practices. This program will be the platform to informing the public on the Governments’ initiatives as well as to promotes products and services offered by Green Catalyst Division.

Objectives

❑ To promote Green Catalyst’s Services such as training program, Green Technology Financial Scheme (GTFS), MyHIJAU Mark Product and Services and Green Incentive (GITA & GITE) to the public and industry players;

❑ To promote green and healthy lifestyle; and

❑ Opportunity for the public to know GreenTech Malaysia.

Theme for GreenTech Run

Don’t be mean, just Go Green! – It simply means changing the way we
live small steps at a time.

GreenTech Run 2019 Details

Date & Venue

Date : 28th December 2019 @ Saturday

Venue : GreenTech Malaysia Office

Program Agenda

TimeProgram
06:30 a.m. – 07:00 a.m.Participant gathered
07:00 a.m. – 07:15 a.m.Warming up sessions (senamrobik) – Special appearance
07:15 a.m.Flag off Category A 10km (Men and Women)
7:20 a.m.Flag off Category B 5km (Men and Women)
7:20 a.m.Category C & D 3km (Adult & Family)
09:45 a.m. – 10:15 a.m.Lucky Draw
10:15 a.m. – 10:45 a.m.Closing and Prize giving ceremony
10:45 a.m. – 11:00 a.m.End of program

Running Kit

Flyers

Banner

Backdrop (on the event day)

Design Arch (on the event day)

Reporting Board (on the event day)

Activities

For the GreenTech Run 2019, we have opened up to 7 types of Category Registration as shown in below table which bring up to the total of 704 participants registered.

CategoryDescription
A10 KM Men Open
B10 KM Women Open
C5 KM Men Open
D5 KM Women Open
E3 KM Men Open
F3 KM Women Open
G3 KM Family (2 Adults & 2 Kids)

Aside to the run, we also have arranged exhibition and trading activities by sponsored companies, food truck, air brush tattoo, lucky draw and MyHIJAU Wheel.

Participants / Audience

The event has been attended by Public, Universities, Industry Players, International and Local Runners, Government Agencies and Ministries. Below is the summary of the registration for the GreenTech Run 2019:

NationalityCount
Indonesia1
India1
Japan3
Kenya4
Malaysia691
Maldives1
Myanmar1
USA2

Outcomes

Below are the outcome of the completed events:

❑ About 60 peoples participated in Quiz & MyHIJAU Wheel to test basic knowledge and help them to improve their knowledge on green technology and climate change.

❑ The publics are aware on the roles and services provided by GreenTech Malaysia

❑ The Partners/ Sponsors exhibit their products and services such as: 

a.         Solar technology

b.         Energy  efficiency technology

c.         Products from recyclable material

d.         Electric vehicles

e.         Eco cleaning products

f.          Biodegradable and compostable products.

❑ Around 704 people participated in the event showing their support in healthy greener lifestyle with no plastic material were used throughout the event

GreenTech Run 2019 Highlight

Warming up session

Below are some pictures taken during the warming up session

During the Run

Below are some pictures taken during the run

The winner for 10km run

Below are pictures of winners for 10km Women run

Below are pictures of winners for 10km Men run

Lucky Draw

Below are pictures of the some lucky draw winners

Sponsors Booth Images

Below are some of the pictures of Sponsors that open their booth on the event day

Sponsor Details

GreenTech Run 2019 become a successful program is because of the sponsor that we have on board. They really give full support and commitment to make sure it success. Thank you for helping us! Below are the list of the companies:

This image is a poster that being published as Slider Image at MyHIJAU Mark Website Slider section from 21 January 2020 till 3rd March 2020.

Interested to joint in our next event? Please do submit your interest via email to admin@mg.myhijau.my.

Showing Archived File

We are glad to inform that we have successfully conducted GreenTech Run 2019 at our office, Malaysian Green Technology Corporation, Bandar Baru Bangi on 28 December 2019. We would like to thanks all the sponsor and all the participants for the run in order to make this event is a success!

Thank you for the effort!

GreenTech Run 2019 Introduction

Background

GreenTech Run 2019 is the first running event organized by Green Catalyst Division under Malaysian Green Technology Corporation (GreenTech Malaysia) with the intention to promotes healthy lifestyle and eco-friendly life by informing the public on the eco-friendly practices. This program will be the platform to informing the public on the Governments’ initiatives as well as to promotes products and services offered by Green Catalyst Division.

Objectives

❑ To promote Green Catalyst’s Services such as training program, Green Technology Financial Scheme (GTFS), MyHIJAU Mark Product and Services and Green Incentive (GITA & GITE) to the public and industry players;

❑ To promote green and healthy lifestyle; and

❑ Opportunity for the public to know GreenTech Malaysia.

Theme for GreenTech Run

Don’t be mean, just Go Green! – It simply means changing the way we
live small steps at a time.

GreenTech Run 2019 Details

Date & Venue

Date : 28th December 2019 @ Saturday

Venue : GreenTech Malaysia Office

Program Agenda

TimeProgram
06:30 a.m. – 07:00 a.m.Participant gathered
07:00 a.m. – 07:15 a.m.Warming up sessions (senamrobik) – Special appearance
07:15 a.m.Flag off Category A 10km (Men and Women)
7:20 a.m.Flag off Category B 5km (Men and Women)
7:20 a.m.Category C & D 3km (Adult & Family)
09:45 a.m. – 10:15 a.m.Lucky Draw
10:15 a.m. – 10:45 a.m.Closing and Prize giving ceremony
10:45 a.m. – 11:00 a.m.End of program

Running Kit

Flyers

Banner

Backdrop (on the event day)

Design Arch (on the event day)

Reporting Board (on the event day)

Activities

For the GreenTech Run 2019, we have opened up to 7 types of Category Registration as shown in below table which bring up to the total of 704 participants registered.

CategoryDescription
A10 KM Men Open
B10 KM Women Open
C5 KM Men Open
D5 KM Women Open
E3 KM Men Open
F3 KM Women Open
G3 KM Family (2 Adults & 2 Kids)

Aside to the run, we also have arranged exhibition and trading activities by sponsored companies, food truck, air brush tattoo, lucky draw and MyHIJAU Wheel.

Participants / Audience

The event has been attended by Public, Universities, Industry Players, International and Local Runners, Government Agencies and Ministries. Below is the summary of the registration for the GreenTech Run 2019:

NationalityCount
Indonesia1
India1
Japan3
Kenya4
Malaysia691
Maldives1
Myanmar1
USA2

Outcomes

Below are the outcome of the completed events:

❑ About 60 peoples participated in Quiz & MyHIJAU Wheel to test basic knowledge and help them to improve their knowledge on green technology and climate change.

❑ The publics are aware on the roles and services provided by GreenTech Malaysia

❑ The Partners/ Sponsors exhibit their products and services such as: 

a.         Solar technology

b.         Energy  efficiency technology

c.         Products from recyclable material

d.         Electric vehicles

e.         Eco cleaning products

f.          Biodegradable and compostable products.

❑ Around 704 people participated in the event showing their support in healthy greener lifestyle with no plastic material were used throughout the event

GreenTech Run 2019 Highlight

Warming up session

Below are some pictures taken during the warming up session

During the Run

Below are some pictures taken during the run

The winner for 10km run

Below are pictures of winners for 10km Women run

Below are pictures of winners for 10km Men run

Lucky Draw

Below are pictures of the some lucky draw winners

Sponsors Booth Images

Below are some of the pictures of Sponsors that open their booth on the event day

Sponsor Details

GreenTech Run 2019 become a successful program is because of the sponsor that we have on board. They really give full support and commitment to make sure it success. Thank you for helping us! Below are the list of the companies:

This image is a poster that being published as Slider Image at MyHIJAU Mark Website Slider section from 21 January 2020 till 3rd March 2020.

Interested to joint in our next event? Please do submit your interest via email to admin@mg.myhijau.my.

GreenTech Run 2019

We are excited to invite you to support us in our fantastic GREENTECH RUN 2019 on 28 December 2019. The running event is meant to promote eco-friendly life by informing the public on the government’s green initiatives as well as to promote products and services by GreenTech Malaysia. Attached herewith is the poster and other information about GREENTECH RUN 2019. All participants will receive a finisher medals, e-certificate, pick up a goody bag, eat tasty treats and have fun! Hope to see you there!!

For online registration, please click
👇👇👇👇👇👇👇
http://bit.ly/37PQCXJ

For any inquiries kindly contact Ms. Umairah at 03-8921 0859

What you will get when you register for this:

Calling for Sponsors

We also open for companies or personnel to sponsor. Please do email us at syamiullah@greentechmalaysia.my. We will send you the details once received the email.

Showing Archived File

We are excited to invite you to support us in our fantastic GREENTECH RUN 2019 on 28 December 2019. The running event is meant to promote eco-friendly life by informing the public on the government’s green initiatives as well as to promote products and services by GreenTech Malaysia. Attached herewith is the poster and other information about GREENTECH RUN 2019. All participants will receive a finisher medals, e-certificate, pick up a goody bag, eat tasty treats and have fun! Hope to see you there!!

For online registration, please click
👇👇👇👇👇👇👇
http://bit.ly/37PQCXJ

For any inquiries kindly contact Ms. Umairah at 03-8921 0859

What you will get when you register for this:

Calling for Sponsors

We also open for companies or personnel to sponsor. Please do email us at syamiullah@greentechmalaysia.my. We will send you the details once received the email.

Product Sharing Session @ LCC 2030 Session #1 on 31 October 2019

On 31 October 2019, GreenTech Malaysia have organized Low Carbon Cities 2030 Challenge: City-Biz Alliance Session #1 – Energy event. Basically this event conducted to assist Local Authorities and Universities in conducting low carbon city activities. The first session is where Solutions Providers related to energy efficiency and sustainable energy were invited to share their products and services.

We have invited some companies to brief on their MyHIJAU Mark recognised products. We have uploaded some of the photos here for sharing purposes.

Company 1: YJC Energy & Resources Sdn. Bhd.

Company 2: Kawasaki Gas Turbine Asia Sdn. Bhd.

Company 3: ABB Malaysia Sdn. Bhd.

Company 4: Multistack Malaysia Sales & Services Sdn. Bhd.

Company 5: Trane Malaysia Sales & Services Sdn. Bhd.

Interest to joint in next session?

We will be having few more session on the other sectors like Building, Transport, Waste & Water. Interested to joint the next session on the sectors that related to your business? Please email us: admin@myhijau.my and state the interest to joint the next event in which sectors.

Showing Archived File

On 31 October 2019, GreenTech Malaysia have organized Low Carbon Cities 2030 Challenge: City-Biz Alliance Session #1 – Energy event. Basically this event conducted to assist Local Authorities and Universities in conducting low carbon city activities. The first session is where Solutions Providers related to energy efficiency and sustainable energy were invited to share their products and services.

We have invited some companies to brief on their MyHIJAU Mark recognised products. We have uploaded some of the photos here for sharing purposes.

Company 1: YJC Energy & Resources Sdn. Bhd.

Company 2: Kawasaki Gas Turbine Asia Sdn. Bhd.

Company 3: ABB Malaysia Sdn. Bhd.

Company 4: Multistack Malaysia Sales & Services Sdn. Bhd.

Company 5: Trane Malaysia Sales & Services Sdn. Bhd.

Interest to joint in next session?

We will be having few more session on the other sectors like Building, Transport, Waste & Water. Interested to joint the next session on the sectors that related to your business? Please email us: admin@myhijau.my and state the interest to joint the next event in which sectors.

MyHIJAU Pavilion 2019 @ IGEM 2019

We are glad to inform that we have successfully conducted MyHIJAU Pavilion 2019 during the International GreenTech & ECO Products Exhibition & Conference Malaysia (IGEM) 2019 in Kuala Lumpur Convention Centre, Malaysia from 9th till 11th October 2019. We would like to thanks all the sponsor in order to make this Pavilion is a success! Thank you for the effort!

MyHIJAU Pavilion Introduction

Objectives

❑ To promote MyHIJAU Mark registered companies and other green companies that exhibit their products, services, projects and technologies to the users and visitors

❑ To introduce government initiatives in green technology development

❑ To provide consultancy services and business collaboration with the ministries, agencies, GLCs, state governments, local authorities and private sector

Concept

The Pavilion are designed to be as a green product/service’s showcase style by Sponsor companies with modern sustainability lifestyle-focused look and feel, giving visitors the opportunity to touch, feel and interact with green products, while also educating them about the new and innovative green offerings and technologies offered by sponsor companies. The theme chosen to be portrayed as “Accelerating the growth of Green Products & Services.

Vision

The vision is to highlight that MyHIJAU does not operate as a Recognition scheme alone and only as online directory, but it is a unifying platform that brings together, individuals, businesses and government bodies to work together in providing a conducive environment for Green Technology development.

Additional

In addition, we have held several activities at the Pavilion itself, for which we have invited relevant partners, stakeholders, and the media to attend. The activities are as listed below:

❑ Networking sessions among our Corporate/Government Stakeholders and Sponsors Companies

❑ Visits by YB Minister, YB KSU and GreenTech Malaysia ACEO

❑ Biz Talk from the participating companies

❑ Pocket Talk @ Hall 5 Pocket Talk Area

Some of the Pavilion panels also highlight the achievements accomplished to date, which includes:

❑ No. of products and services registered under MyHIJAU Mark

❑ No. of companies registered under MyHIJAU Mark

❑ No. of application approved under the MyHIJAU Mark

❑ Number of GGP criteria developed for green products and services

MyHIJAU Pavilion Overall Image

Below we have enclosed some of the Pavilion images.

MyHIJAU Pavilion Advertisement

We have published an advertisement page in the New Straits Time (NST) on 8th October 2019 (Tuesday), a day before the event day to highlight on MyHIJAU Pavilion @ IGEM 2019. In the page, we have highlighted on the sponsors that really support us on this effort. Below is the published advert (Designer File) and the link below is the actual Advertisement page published.

Actual NST Advertisement PageDownload

Highlight of the Pavilion

Visit by VIPs

During the event, we have received visit from YB Minister, YB Puan Yeo Bee Yin (Day 2), KSU; YBhg. Datuk Seri Dr. Mohd Azhar Hj Yahaya (Day 3) and GreenTech Malaysia ACEO; Tn. Syed Ahmad Syed Mustafa (Day 3). We are really honored to have visited our pavilion. Below are some images:

Biz Talk Session @ MyHIJAU Pavilion

In conjunction with this pavilion, we have conducted Biz Talk Session (Day 1, 2 and 3) for the pavilion sponsors companies to brief on their green product / services. For the participants it comes from the sponsor companies invitation together with our side invitation within our contact. We have also shared flyers on the day of the event (Day 1, 2 and 3). Enclosed is the posters which shows the details of the session:

Pocket Talk Session

At the same time we have arranged few Pocket Talk slots at the Hall 5 Pocket Talk area during this IGEM 2019 for Title and Platinum Sponsor companies. Not to miss the chances, we have also arranged slots for MyHIJAU Mark, Green Incentives (GITA/GITE) and GTFS 2.0 talks. The details are as below:

Sponsor Details

MyHIJAU Pavilion become a successful program is because of the sponsor that we have on board. They really give full support and commitment to make sure it success. Below are the list of the companies logo:

This image is a poster that being published as Slider Image at MyHIJAU Mark Website Slider section from end of October 2019 till 3rd March 2020.

Commitment for 2020 event?

Due to the success on the 1st MyHIJAU Pavilion and we have received positive response on it, we would like to open for booking for companies that are interested to commit to participate in next year MyHIJAU Pavilion @ iGEM 2020. Please submit your interest via email to admin@myhijau.my stating the interest to participate and provide us the contact person whom can liaise with.

Showing Archived File

We are glad to inform that we have successfully conducted MyHIJAU Pavilion 2019 during the International GreenTech & ECO Products Exhibition & Conference Malaysia (IGEM) 2019 in Kuala Lumpur Convention Centre, Malaysia from 9th till 11th October 2019. We would like to thanks all the sponsor in order to make this Pavilion is a success! Thank you for the effort!

MyHIJAU Pavilion Introduction

Objectives

❑ To promote MyHIJAU Mark registered companies and other green companies that exhibit their products, services, projects and technologies to the users and visitors

❑ To introduce government initiatives in green technology development

❑ To provide consultancy services and business collaboration with the ministries, agencies, GLCs, state governments, local authorities and private sector

Concept

The Pavilion are designed to be as a green product/service’s showcase style by Sponsor companies with modern sustainability lifestyle-focused look and feel, giving visitors the opportunity to touch, feel and interact with green products, while also educating them about the new and innovative green offerings and technologies offered by sponsor companies. The theme chosen to be portrayed as “Accelerating the growth of Green Products & Services.

Vision

The vision is to highlight that MyHIJAU does not operate as a Recognition scheme alone and only as online directory, but it is a unifying platform that brings together, individuals, businesses and government bodies to work together in providing a conducive environment for Green Technology development.

Additional

In addition, we have held several activities at the Pavilion itself, for which we have invited relevant partners, stakeholders, and the media to attend. The activities are as listed below:

❑ Networking sessions among our Corporate/Government Stakeholders and Sponsors Companies

❑ Visits by YB Minister, YB KSU and GreenTech Malaysia ACEO

❑ Biz Talk from the participating companies

❑ Pocket Talk @ Hall 5 Pocket Talk Area

Some of the Pavilion panels also highlight the achievements accomplished to date, which includes:

❑ No. of products and services registered under MyHIJAU Mark

❑ No. of companies registered under MyHIJAU Mark

❑ No. of application approved under the MyHIJAU Mark

❑ Number of GGP criteria developed for green products and services

MyHIJAU Pavilion Overall Image

Below we have enclosed some of the Pavilion images.

MyHIJAU Pavilion Advertisement

We have published an advertisement page in the New Straits Time (NST) on 8th October 2019 (Tuesday), a day before the event day to highlight on MyHIJAU Pavilion @ IGEM 2019. In the page, we have highlighted on the sponsors that really support us on this effort. Below is the published advert (Designer File) and the link below is the actual Advertisement page published.

Actual NST Advertisement PageDownload

Highlight of the Pavilion

Visit by VIPs

During the event, we have received visit from YB Minister, YB Puan Yeo Bee Yin (Day 2), KSU; YBhg. Datuk Seri Dr. Mohd Azhar Hj Yahaya (Day 3) and GreenTech Malaysia ACEO; Tn. Syed Ahmad Syed Mustafa (Day 3). We are really honored to have visited our pavilion. Below are some images:

Biz Talk Session @ MyHIJAU Pavilion

In conjunction with this pavilion, we have conducted Biz Talk Session (Day 1, 2 and 3) for the pavilion sponsors companies to brief on their green product / services. For the participants it comes from the sponsor companies invitation together with our side invitation within our contact. We have also shared flyers on the day of the event (Day 1, 2 and 3). Enclosed is the posters which shows the details of the session:

Pocket Talk Session

At the same time we have arranged few Pocket Talk slots at the Hall 5 Pocket Talk area during this IGEM 2019 for Title and Platinum Sponsor companies. Not to miss the chances, we have also arranged slots for MyHIJAU Mark, Green Incentives (GITA/GITE) and GTFS 2.0 talks. The details are as below:

Sponsor Details

MyHIJAU Pavilion become a successful program is because of the sponsor that we have on board. They really give full support and commitment to make sure it success. Below are the list of the companies logo:

This image is a poster that being published as Slider Image at MyHIJAU Mark Website Slider section from end of October 2019 till 3rd March 2020.

Commitment for 2020 event?

Due to the success on the 1st MyHIJAU Pavilion and we have received positive response on it, we would like to open for booking for companies that are interested to commit to participate in next year MyHIJAU Pavilion @ iGEM 2020. Please submit your interest via email to admin@myhijau.my stating the interest to participate and provide us the contact person whom can liaise with.

CALLING FOR MyHIJAU PAVILION SPONSORSHIP

Check out the benefits why you should sign up to become a MyHIJAU Pavilion 2019 sponsor

SPECIAL PACKAGE

Earn Thousands of Event Impressions:

TITLE SPONSOR (RM 80,000.00)

What you will receive:

Guaranteed For The Following Amazing Benefits:

PLATINUM PACKAGE (RM 30,000.00)

What you will receive:

Click below button to download the brochure

For more information on the above available programs, please click the below link:

Energy Manager Convention 2019

Energy Manager Training

Certified Professional in Measurement Verification

Green Technology Financing Scheme (GTFS)

OTHER PACKAGES

Get privilege for below packages:

GOLD PACKAGE (RM 20,000.00)

What you will receive if you are under:

MyHIJAU Mark Companies

Green Local Companies

For more information on the above available programs, please click the below link:

Energy Manager Convention 2019

Energy Manager Training

Certified Professional in Measurement Verification

Green Technology Financing Scheme (GTFS)

Join our ranks with other great brands companies with below benefits:

SILVER PACKAGE (RM 5,000.00)

What you will receive if you are under:

MyHIJAU Mark Companies

Green Local Companies

For more information on the above available programs, please click the below link:

Energy Manager Training

Certified Professional in Measurement Verification

IMPORTANT:   Please note, the sponsorship call will close on the 10th of September 2019.

EXPRESS YOUR INTEREST

If you are interested to sponsor MyHIJAU Pavillion2019, please submit your confirmation  through the online form and we will contact you as soon as possible. In case you have any further questions, please do not hesitate to contact us at admin@myhijau.my or call Mr. Syamiullah Mohd Gani or Ms. Nur Syahira Abdul Rahim  at 03-8921 0874 / 03-8921 0983.

Click below button to download the brochure

Showing Archived File

Check out the benefits why you should sign up to become a MyHIJAU Pavilion 2019 sponsor

SPECIAL PACKAGE

Earn Thousands of Event Impressions:

TITLE SPONSOR (RM 80,000.00)

What you will receive:

Guaranteed For The Following Amazing Benefits:

PLATINUM PACKAGE (RM 30,000.00)

What you will receive:

Click below button to download the brochure

For more information on the above available programs, please click the below link:

Energy Manager Convention 2019

Energy Manager Training

Certified Professional in Measurement Verification

Green Technology Financing Scheme (GTFS)

OTHER PACKAGES

Get privilege for below packages:

GOLD PACKAGE (RM 20,000.00)

What you will receive if you are under:

MyHIJAU Mark Companies

Green Local Companies

For more information on the above available programs, please click the below link:

Energy Manager Convention 2019

Energy Manager Training

Certified Professional in Measurement Verification

Green Technology Financing Scheme (GTFS)

Join our ranks with other great brands companies with below benefits:

SILVER PACKAGE (RM 5,000.00)

What you will receive if you are under:

MyHIJAU Mark Companies

Green Local Companies

For more information on the above available programs, please click the below link:

Energy Manager Training

Certified Professional in Measurement Verification

IMPORTANT:   Please note, the sponsorship call will close on the 10th of September 2019.

EXPRESS YOUR INTEREST

If you are interested to sponsor MyHIJAU Pavillion2019, please submit your confirmation  through the online form and we will contact you as soon as possible. In case you have any further questions, please do not hesitate to contact us at admin@myhijau.my or call Mr. Syamiullah Mohd Gani or Ms. Nur Syahira Abdul Rahim  at 03-8921 0874 / 03-8921 0983.

Click below button to download the brochure

MyHIJAU eBooks Available Now

Download eBook now to have latest compiled list and event can be used when offline! This eBook has paid advertisement slot for you to share about your product or services.

Download

MyHIJAU App Available Now

Download now to keep updated and have latest listings with you all the time!

  • A Flagship Project By:
    MGTC
  • Endorsed By:
    MYHIJAU